fd — floppy disk device


Floppy drives are block devices with major number 2. Typically they are owned by root:floppy (i.e., user root, group floppy) and have either mode 0660 (access checking via group membership) or mode 0666 (everybody has access). The minor numbers encode the device type, drive number, and controller number. For each device type (that is, combination of density and track count) there is a base minor number. To this base number, add the drive's number on its controller and 128 if the drive is on the secondary controller. In the following device tables, n represents the drive number.

if you use formats with more tracks than supported by your drive, you may cause it mechanical damage. Trying once if more tracks than the usual 40/80 are supported should not damage it, but no warranty is given for that. If you are not sure, don't create device entries for those formats, so as to prevent their usage.

Drive-independent device files which automatically detect the media format and capacity:

Name Base minor #
fdn 0

5.25 inch double-density device files:

Name Capacity Cyl. Sect. Heads Base
  KiB       minor #
fdnd360 360 40 9 2 4

5.25 inch high-density device files:

Name Capacity Cyl. Sect. Heads Base
  KiB       minor #
fdnh360 360 40 9 2 20
fdnh410 410 41 10 2 48
fdnh420 420 42 10 2 64
fdnh720 720 80 9 2 24
fdnh880 880 80 11 2 80
fdnh1200 1200 80 15 2 8
fdnh1440 1440 80 18 2 40
fdnh1476 1476 82 18 2 56
fdnh1494 1494 83 18 2 72
fdnh1600 1600 80 20 2 92

3.5 inch double-density device files:

Name Capacity Cyl. Sect. Heads Base
  KiB       minor #
fdnu360 360 80 9 1 12
fdnu720 720 80 9 2 16
fdnu800 800 80 10 2 120
fdnu1040 1040 80 13 2 84
fdnu1120 1120 80 14 2 88

3.5 inch high-density device files:

Name Capacity Cyl. Sect. Heads Base
  KiB       minor #
fdnu360 360 40 9 2 12
fdnu720 720 80 9 2 16
fdnu820 820 82 10 2 52
fdnu830 830 83 10 2 68
fdnu1440 1440 80 18 2 28
fdnu1600 1600 80 20 2 124
fdnu1680 1680 80 21 2 44
fdnu1722 1722 82 21 2 60
fdnu1743 1743 83 21 2 76
fdnu1760 1760 80 22 2 96
fdnu1840 1840 80 23 2 116
fdnu1920 1920 80 24 2 100

3.5 inch extra-density device files:

Name Capacity Cyl. Sect. Heads Base
  KiB       minor #
fdnu2880 2880 80 36 2 32
fdnCompaQ 2880 80 36 2 36
fdnu3200 3200 80 40 2 104
fdnu3520 3520 80 44 2 108
fdnu3840 3840 80 48 2 112


fd special files access the floppy disk drives in raw mode. The following ioctl(2) calls are supported by fd devices:


clears the media information of a drive (geometry of disk in drive).


sets the media information of a drive. The media information will be lost when the media is changed.


sets the media information of a drive (geometry of disk in drive). The media information will not be lost when the media is changed. This will disable autodetection. In order to reenable autodetection, you have to issue an FDCLRPRM.


returns the type of a drive (name parameter). For formats which work in several drive types, FDGETDRVTYP returns a name which is appropriate for the oldest drive type which supports this format.


invalidates the buffer cache for the given drive.


sets the error thresholds for reporting errors, aborting the operation, recalibrating, resetting, and reading sector by sector.


gets the current error thresholds.


gets the internal name of the drive.


clears the write error statistics.


reads the write error statistics. These include the total number of write errors, the location and disk of the first write error, and the location and disk of the last write error. Disks are identified by a generation number which is incremented at (almost) each disk change.


Switch the drive motor off for a few microseconds. This might be needed in order to access a disk whose sectors are too close together.


sets various drive parameters.


reads these parameters back.


gets the cached drive state (disk changed, write protected et al.)


polls the drive and return its state.


gets the floppy controller state.


resets the floppy controller under certain conditions.


sends a raw command to the floppy controller.

For more precise information, consult also the <linux/fd.h> and <linux/fdreg.h> include files, as well as the floppycontrol(1) manual page.




The various formats permit reading and writing many types of disks. However, if a floppy is formatted with an inter-sector gap that is too small, performance may drop, to the point of needing a few seconds to access an entire track. To prevent this, use interleaved formats.

It is not possible to read floppies which are formatted using GCR (group code recording), which is used by Apple II and Macintosh computers (800k disks).

Reading floppies which are hard sectored (one hole per sector, with the index hole being a little skewed) is not supported. This used to be common with older 8-inch floppies.


chown(1), floppycontrol(1), getfdprm(1), mknod(1), superformat(1), mount(8), setfdprm(8)


This page is part of release 5.11 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at−pages/.

  Copyright (c) 1993 Michael Haardt (
and 1994,1995 Alain Knaff (

This is free documentation; you can redistribute it and/or
modify it under the terms of the GNU General Public License as
published by the Free Software Foundation; either version 2 of
the License, or (at your option) any later version.

The GNU General Public License's references to "object code"
and "executables" are to be interpreted as the output of any
document formatting or typesetting system, including
intermediate and printed output.

This manual is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
GNU General Public License for more details.

You should have received a copy of the GNU General Public
License along with this manual; if not, see

Modified, Sun Feb 26 15:00:02 1995,